ENetwork Basic Configuration PT Practice SBA

CISCO NETWORKING ACADEMY – ENetwork Basic Configuration PT Practice SBA – QUESTIONS

A few things to keep in mind while completing this activity:

1. Do not use the browserBac k button or close or reload any Exam windows during the exam.

2. Do not close Packet Tracer when you are done. It will close automatically.

3. Click the Submit Assessment button to submit your work.

 

Introduction

In this practice Packet Tracer Skills Exam, you will:

 finish connecting the devices

 design and implement an addressing scheme to meet stated requirements

 configure, verify, and troubleshoot connectivity between all devices in the network

Addressing Table

NOTE: The initial network has some errors. To aid in configuring and verifying the devices as well troubleshooting the existing errors, use a printed version of these instructions to fill inthe missing address information in the table during Step 2.

 

Step 1: Connect the Devices.

Connect the following devices using the appropriate cable:

a. Connect PC1 to Switch1.

b. Connect Switch1 to the Fa0/0 interface on Router1.

c. Connect Switch2 to the Fa0/1 interface on Router1.

d. Connect PC1 to the Router1 console port.

 

Step 2: Determine the IP Addressing Scheme.

Design an addressing scheme and fill in the Addressing Table based on the following requirements:

a. Subnet the address space 172.16.1.0/24 to provide 30 host addresses for LAN 1 while wasting the least amount of address space.

b. Assign the first available subnet to LAN 1.

c. Assign the lowest (first) host address in this subnet to the Fa0/0 interface on Router1.

d. Assign the second address in this subnet to the VLAN 1 interface on Switch1.

e. Assign the highest (last) host IP address in this subnet to PC1.

f. Using the next available subnet, further subnet it to provide 10 host addresses for LAN2 while wasting the least amount of address space.

g. Assign the lowest (first) host address in the LAN2 subnet to the Fa0/1 interface on Router1.

 

Step 3: Configure Router1.

a. Configure Router1 with the following basic parameters:

· The router name is Router1.

· The privileged EXEC mode uses the following encrypted password: class

· Enable Telnet and console line login using the following password: cisco

· Configure the banner message-of-the-day as Authorized access only!

b. Configure the two Fast Ethernet interfaces, including addressing and a description.

c. Close the terminal window after completing the router configuration.

 

Step 4: Configure Switch1 and Verify Connectivity.

a. Remove the console connection between PC1 and Router1.

b. Connect PC1 to the Switch1 console port.

c. Configure Switch1 with the following basic parameters:

· The switch name is Switch1

· The privileged EXEC mode uses the following encrypted password: class

· Enable Telnet and console line login using the following password: cisco

· Configure the banner message-of-the-day as Authorized access only!

d.Configure interface VLAN 1 and default gateway for Switch1.

e.Switch1 should be able to ping the default gateway.

 

Step 5: Configure and Verify PC1 Addressing.

a. Using the IP addressing you determined in Step 2, configure PC1 with the correct addressing.

b. PC1 should be able to ping the default gateway.

 

Step 6: Verify and Troubleshoot End-to-End Connectivity.

Verify that PC1 is able to ping PC2. If the ping fails, locate and correct any errors. For example, make sure PC2 is configured correctly with appropriate addressing for the subnet it belongs to.

 

 

ENetwork Basic Configuration PT Practice SBA  –  ANSWERS

 

Step 1: Connect the Devices.

Connect the following devices using the appropriate cable:

a. Connect PC1 to Switch1.

b. Connect Switch1 to the Fa0/0 interface on Router1.

c. Connect Switch2 to the Fa0/1 interface on Router1.

d. Connect PC1 to the Router1 console port.

 

 

Step 2: Determine the IP Addressing Scheme.

 

Design an addressing scheme and fill in the Addressing Table based on the following requirements:

a. Subnet the address space 172.16.1.0/24 to provide 30 host addresses for LAN 1 while wasting the least amount of address space.

b. Assign the first available subnet to LAN 1.

c. Assign the lowest (first) host address in this subnet to the Fa0/0 interface on

Router1.

d. Assign the second address in this subnet to the VLAN 1 interface on Switch1

e. Assign the highest (last) host IP address in this subnet to PC1.

f. Using the next available subnet, further subnet it to provide 10 host addresses for LAN2 while wasting the least amount of address space.

g. Assign the lowest (first) host address in the LAN2 subnet to the Fa0/1 interface on Router1.

 

Step 3: Configure Router1.

 

a. Configure Router1 with the following basic parameters:

The router name is Router1.

Router>enable

Router#config terminal

Router(config)#hostname Router1

The privileged EXEC mode uses the following encrypted password: class

Router1(config)#enable secret class

Router1(config)#service password-encryption

Router1(config)#line console 0

Router1(config) #password cisco

Router1(config)#login

Enable Telnet and console line login using the following password: cisco

Router1(config)#line vty 0 4

Router1(config-line)#password cisco

Router1(config-line)#login

Router1(config-line)#exit

Configure the banner message-of-the-day as Authorized access only!

Router1(config)#banner motd # Authorized access only! #

 

b. Configure the two Fast Ethernet interfaces, including addressing and a description.

Router1(config)#interface fastethernet 0/0

Router1(config-if)#ip addres 172.16.1.1 255.255.255.224

Router1(config-if)#description LAN1

Router1(config-if)#no shutdown

Router1(config-if)#exit

 

Router1(config)#interface fastethernet 0/1

Router1(config-if)#ip addres 172.16.1.33 255.255.255.240

Router1(config-if)#description LAN2

Router1(config-if)#no shutdown

Router1(config-if)#exit

Router1(config)#exit

Router1#write

c. Close the terminal window after completing the router configuration.

 

Step 4: Configure Switch1 and Verify Connectivity.

a. Remove the console connection between PC1 and Router1.

b. Connect PC1 to the Switch1 console port.

c. Configure Switch1 with the following basic parameters:

The switch name is Switch1

Switch>enable

Swich#config terminal

Switch(config)#hostname Switch1

The privileged EXEC mode uses the following encrypted password: class

Switch1(config)#enable secret class

Switch1(config)#service password-encryption

Switch1(config)#line console 0

Switch1(config)#password cisco

Switch1(config)#login

Enable Telnet and console line login using the following password: cisco

Switch1(config)#line vty 0 15

Switch1(config-line)#password cisco

Switch1(config-line)#login

Switch1(config-line)#exit

Configure the banner message-of-the-day as Authorized access only!

Switch1(config)#banner motd # Authorized access only! #

 

d. Configure interface VLAN 1 and default gateway for Switch1.

Switch1(config)#ip default-gateway 172.16.1.1

Switch1(config)#interface vlan 1

Switch1(config-if)#ip address 172.16.1.2 255.255.255.224

Switch1(config-if)#no shutdown

Switch1(config-if)#exit

 

e. Switch1 should be able to ping the default gateway.

 

Step 5: Configure and Verify PC1 Addressing.

a. Using the IP addressing you determined in Step 2, configure PC1 with the correct

addressing.

b. PC1 should be able to ping the default gateway.

 

Step 6: Verify and Troubleshoot End-to-End Connectivity.

Verify that PC1 is able to ping PC2. If the ping fails, locate and correct any errors. For example, make sure PC2 is configured correctly with appropriate addressing for the subnet it belongs to.

* Replace cable to PC2 with a direct SW2.

 

The result is 100%.

Tinggalkan Balasan

Isikan data di bawah atau klik salah satu ikon untuk log in:

Logo WordPress.com

You are commenting using your WordPress.com account. Logout / Ubah )

Gambar Twitter

You are commenting using your Twitter account. Logout / Ubah )

Foto Facebook

You are commenting using your Facebook account. Logout / Ubah )

Foto Google+

You are commenting using your Google+ account. Logout / Ubah )

Connecting to %s