CCNA 1 Chapter 11

Cisco CCNA1-Chapter-11  Correct Questions Answers 100%

1. Users in the network are experiencing slow response time when doing file transfers to a remote server. What command could be issued to determine if the router has experienced any input or output errors?

  • show running-config;
  • show startup-config;
  • show interfaces ;
  • show ip route;
  • show version;
  • show memory.

2.  Refer to the exhibit. A technician applies the configuration in the exhibit to a clean router. To verify the configuration, the technician issues the show running-config command in the CLI session with the router. What lines should the technician expect to see in the router output from the show   running-config command?

  • enable password class

line console 0
password ccna;

  • enable secret cisco

enable password class
line console 0
password ccna;

  • enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0enable

password class
line console  0
password ccna;

  • enable secret ciscoenable password 7 14141E0A1F17

line console 0
password 7 020507550A;

  • enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0enable

                      password 7 14141E0A1F17
                      line console 0
                     password 7 020507550A ;

3.  Refer to the exhibit. A network administrator on HostA has problems accessing the FTP server. Layer three connectivity testing was successful from HostA to the S1 interface of
RouterB. Which set of commands will allow the network administrator to telnet to RouterB and run debug commands?

  • RouterB(config)# enable secret class

RouterB(config)# line vty 0 4
RouterB(config-if)# login

  • RouterB(config)# enable secret class

RouterB(config)# line vty 0 2
RouterB(config-vty)# password cisco
RouterB(config-vty)# login

  • RouterB(config)# enable secret class

RouterB(config)# line vty 0
RouterB(config-line)# password cisco
RouterB(config-line)# login

  • RouterB(config)# enable secret class

RouterB(config)# line aux 0
RouterB(config-line)# password cisco
RouterB(config-line)# login

  • RouterB(config)# enable secret class

RouterB(config)# line aux 0
RouterB(config-vty)# password cisco
RouterB(config-vty)# login

4.  Refer to the exhibit. The output is shown for the show ip route command executed on Router A. What does the IP address 192.168.2.2 represent?

  • Gateway for the 192.168.1.0 network;
  • Gateway for the 192.168.3.0 network;
  • IP assigned to the serial port on Router A;
  • IP assigned to the serial port on Router B.

5. What command is used to change the default router name to Fontana?

  • Router# name Fontana;
  • Router# hostname Fontana;
  • Router(config)# name Fontana;
  • Router(config)# hostname Fontana.

6.   The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)

  • Sydney(config-if)# ip address 201.100.53.2 255.255.255.0 ;
  • Sydney(config-if)# no shutdown ;
  • Sydney(config-if)# ip address 201.100.53.1 255.255.255.224 ;
  • Sydney(config-if)# clock rate 56000 ;
  • Sydney(config-if)# ip host Melbourne 201.100.53.2 .

7.  Refer to the exhibit. What additional command is required to allow remote access to this switch?

  • NA-SW1(config-if)# no shutdown;
  • NA-SW1(config)# enable password password;
  • NA-SW1(config)# ip default-gateway address ;
  • NA-SW1(config-if)# description description .

8. When network services fail, which port is most often used to access a router for management purposes?

  • AUX;
  • Ethernet;
  • Console ;
  • Telnet ;
  • SSH .

9. A network administrator needs to keep the user ID, password, and session contents private when establishing remote CLI connectivity with a router to manage it. Which access method should be chosen?

  • Telnet;
  • Console;
  • AUX;
  • SSH.

10. In a Cisco router, when do changes made to the running-configuration take effect?

  • after a system restart;
  • as the commands are entered ;
  • when logging off the system;
  • when the configuration is saved to the startup-configuration;

11.  Refer to the exhibit. Which names correctly identify the CLI mode represented by the prompt for Switch-East4#? (Choose two.)

  • line configuration mode;
  • user executive mode;
  • global configuration mode;
  • privileged executive mode ;
  • interface configuration mode ;
  • enable mode .

12. Which three terms correctly define the forms of help available within the Cisco IOS? (Choose three.)

  • hot keys ;
  • context-check ;
  • context-sensitive ;
  • structured check ;
  • command override ;
  • command syntax check .

13. Which combination of keys would be used at the CLI prompt to interrupt a ping or traceroute
process?

  • Ctrl-C;
  • Ctrl-P;
  • Ctrl-R;
  • Ctrl-Shift-6 ;
  • Ctrl-Z .

14.  Refer to the exhibit. What command will place the router into the correct mode to configure an appropriate interface to connect to a LAN?

  • UBAMA# configure terminal;
  • UBAMA(config)# line vty 0 4 ;
  • UBAMA(config)# line console 0;
  • UBAMA(config)# interface Serial 0/0/0;
  • UBAMA(config)# interface FastEthernet 0/1.

15. On a Cisco router, which interface would be used to make the initial configuration?

                                            

Console Port —this

16.  Refer to the exhibit. A student is responsible for the IP addressing, configuration and connectivity testing of the network shown in the graphic. A ping from host B to host C results in a destination unreachable but a ping from host B to host A was successful. What two reasons could account for this failure based on the graphic and partial router output for the Dallas router? (Choose two.)

  • The host A is turned off;
  • The Fa0/0 interface on Dallas is shutdown;
  • The LAN cable is disconnected from host B;
  • The S0/0/1 IP address of Dallas is improperly configured;
  • The Fa0/0 interface on Dallas is in a different subnet than host B;
  • The clock rate is missing on the serial link between Dallas and NYC.

17. In a CISCO device, where is the IOS file stored prior to system startup ?

  • RAM;
  • ROM;
  • Flash;
  • NVRAM.

18.   The connection between routers B and C has been successfully tested. However, after rebooting router C, the administrator noticed the response time between networks 10.10.3.0 and 10.10.4.0 is slower. Ping between the two routers is successful. A trace route indicates three hops from router B to router C. What else can be done to troubleshoot the problem?

  • Ping router B S0/1 connection from router C;
  • Trace the connection between router B to router C S0/1;
  • Issue a show ip route command in router B to verify routing is enabled;
  • Issue a show ip interface brief command on router C.

19. Immediately after a router completes its boot sequence, the network administrator wants to check the routers configuration. From privileged EXEC mode, which of the following commands can the administrator use for this purpose? (Choose two.)

Tinggalkan Balasan

Isikan data di bawah atau klik salah satu ikon untuk log in:

Logo WordPress.com

You are commenting using your WordPress.com account. Logout / Ubah )

Gambar Twitter

You are commenting using your Twitter account. Logout / Ubah )

Foto Facebook

You are commenting using your Facebook account. Logout / Ubah )

Foto Google+

You are commenting using your Google+ account. Logout / Ubah )

Connecting to %s